[PATCH] prep_pci.c: replace pci_find_device with pci_get_device

Signed-off-by: Hanna Linder <hannal@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

diff --git a/arch/ppc/platforms/prep_pci.c b/arch/ppc/platforms/prep_pci.c
index a528562ccf16844dac89c0418e522eef9604eb72..d7abcbe8cc03e78a1a8ae9b97c58f753893647c6 100644 (file)
--- a/arch/ppc/platforms/prep_pci.c
+++ b/arch/ppc/platforms/prep_pci.c
@@ -1069,7 +1069,7 @@ prep_pib_init(void)
                 * Perform specific configuration for the Via Tech or
                 * or Winbond PCI-ISA-Bridge part.
                 */
-               if ((dev = pci_find_device(PCI_VENDOR_ID_VIA,
+               if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
                                        PCI_DEVICE_ID_VIA_82C586_1, dev))) {
                        /*
                         * PPCBUG does not set the enable bits
@@ -1080,7 +1080,7 @@ prep_pib_init(void)
                        reg |= 0x03; /* IDE: Chip Enable Bits */
                        pci_write_config_byte(dev, 0x40, reg);
                }
-               if ((dev = pci_find_device(PCI_VENDOR_ID_VIA,
+               if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
                                                PCI_DEVICE_ID_VIA_82C586_2,
                                                dev)) && (dev->devfn = 0x5a)) {
                        /* Force correct USB interrupt */
@@ -1089,7 +1089,7 @@ prep_pib_init(void)
                                        PCI_INTERRUPT_LINE,
                                        dev->irq);
                }
-               if ((dev = pci_find_device(PCI_VENDOR_ID_WINBOND,
+               if ((dev = pci_get_device(PCI_VENDOR_ID_WINBOND,
                                        PCI_DEVICE_ID_WINBOND_83C553, dev))) {
                         /* Clear PCI Interrupt Routing Control Register. */
                        short_reg = 0x0000;
@@ -1100,9 +1100,10 @@ prep_pib_init(void)
                                pci_write_config_byte(dev, 0x43, reg);
                        }
                }
+               pci_dev_put(dev);
        }
 
-       if ((dev = pci_find_device(PCI_VENDOR_ID_WINBOND,
+       if ((dev = pci_get_device(PCI_VENDOR_ID_WINBOND,
                                   PCI_DEVICE_ID_WINBOND_82C105, dev))){
                if (OpenPIC_Addr){
                        /*
@@ -1121,6 +1122,7 @@ prep_pib_init(void)
                        pci_write_config_dword(dev, 0x40, 0x10ff08a1);
                }
        }
+       pci_dev_put(dev);
 }
 
 static void __init
@@ -1207,7 +1209,7 @@ prep_pcibios_fixup(void)
        printk("Setting PCI interrupts for a \"%s\"\n", Motherboard_map_name);
 
        /* Iterate through all the PCI devices, setting the IRQ */
-       while ((dev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, dev)) != NULL) {
+       for_each_pci_dev(dev) {
                /*
                 * If we have residual data, then this is easy: query the
                 * residual data for the IRQ line allocated to the device.
@@ -1260,12 +1262,13 @@ prep_pcibios_after_init(void)
         * instead of 0xc0000. vgacon.c (for example) is completely unaware of
         * this little quirk.
         */
-       dev = pci_find_device(PCI_VENDOR_ID_WD, PCI_DEVICE_ID_WD_90C, NULL);
+       dev = pci_get_device(PCI_VENDOR_ID_WD, PCI_DEVICE_ID_WD_90C, NULL);
        if (dev) {
                dev->resource[1].end -= dev->resource[1].start;
                dev->resource[1].start = 0;
                /* tell the hardware */
                pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 0x0);
+               pci_dev_put(dev);
        }
 #endif
 }