Let's just get over with this before queue handling will be targeted again...
- Implement suggestions by Russell King for improved portability and separation
between PCI and non PCI host code.
- pdc202xxx updates from Thierry Vignaud.
- Tiny PIO fix from Tomita.
O_TARGET := idedriver.o
-export-objs := ide-taskfile.o ide.o ide-features.o ide-probe.o ide-dma.o ataraid.o
+export-objs := ide-taskfile.o ide.o ide-features.o ide-probe.o quirks.o pcidma.o ataraid.o
obj-y :=
obj-m :=
ide-obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o
ide-obj-$(CONFIG_BLK_DEV_HT6560B) += ht6560b.o
ide-obj-$(CONFIG_BLK_DEV_IDE_ICSIDE) += icside.o
-ide-obj-$(CONFIG_BLK_DEV_IDEDMA_PCI) += ide-dma.o
+ide-obj-$(CONFIG_BLK_DEV_IDEDMA) += quirks.o
+ide-obj-$(CONFIG_BLK_DEV_IDEDMA_PCI) += pcidma.o
ide-obj-$(CONFIG_BLK_DEV_IDE_TCQ) += tcq.o
ide-obj-$(CONFIG_PCI) += ide-pci.o
ide-obj-$(CONFIG_BLK_DEV_ISAPNP) += ide-pnp.o
+++ /dev/null
-/**** vi:set ts=8 sts=8 sw=8:************************************************
- *
- * Copyright (c) 1999-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (c) 1995-1998 Mark Lord
- *
- * May be copied or modified under the terms of the GNU General Public License
- *
- * Special Thanks to Mark for his Six years of work.
- *
- * This module provides support for the bus-master IDE DMA functions
- * of various PCI chipsets, including the Intel PIIX (i82371FB for
- * the 430 FX chipset), the PIIX3 (i82371SB for the 430 HX/VX and
- * 440 chipsets), and the PIIX4 (i82371AB for the 430 TX chipset)
- * ("PIIX" stands for "PCI ISA IDE Xcellerator").
- *
- * Pretty much the same code works for other IDE PCI bus-mastering chipsets.
- *
- * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies).
- *
- * By default, DMA support is prepared for use, but is currently enabled only
- * for drives which already have DMA enabled (UltraDMA or mode 2 multi/single),
- * or which are recognized as "good" (see table below). Drives with only mode0
- * or mode1 (multi/single) DMA should also work with this chipset/driver
- * (eg. MC2112A) but are not enabled by default.
- *
- * Use "hdparm -i" to view modes supported by a given drive.
- *
- * The hdparm-3.5 (or later) utility can be used for manually enabling/disabling
- * DMA support, but must be (re-)compiled against this kernel version or later.
- *
- * To enable DMA, use "hdparm -d1 /dev/hd?" on a per-drive basis after booting.
- * If problems arise, ide.c will disable DMA operation after a few retries.
- * This error recovery mechanism works and has been extremely well exercised.
- *
- * IDE drives, depending on their vintage, may support several different modes
- * of DMA operation. The boot-time modes are indicated with a "*" in
- * the "hdparm -i" listing, and can be changed with *knowledgeable* use of
- * the "hdparm -X" feature. There is seldom a need to do this, as drives
- * normally power-up with their "best" PIO/DMA modes enabled.
- *
- * Testing has been done with a rather extensive number of drives,
- * with Quantum & Western Digital models generally outperforming the pack,
- * and Fujitsu & Conner (and some Seagate which are really Conner) drives
- * showing more lackluster throughput.
- *
- * Keep an eye on /var/adm/messages for "DMA disabled" messages.
- *
- * Some people have reported trouble with Intel Zappa motherboards.
- * This can be fixed by upgrading the AMI BIOS to version 1.00.04.BS0,
- * available from ftp://ftp.intel.com/pub/bios/10004bs0.exe
- * (thanks to Glen Morrell <glen@spin.Stanford.edu> for researching this).
- *
- * Thanks to "Christopher J. Reimer" <reimer@doe.carleton.ca> for
- * fixing the problem with the BIOS on some Acer motherboards.
- *
- * Thanks to "Benoit Poulot-Cazajous" <poulot@chorus.fr> for testing
- * "TX" chipset compatibility and for providing patches for the "TX" chipset.
- *
- * Thanks to Christian Brunner <chb@muc.de> for taking a good first crack
- * at generic DMA -- his patches were referred to when preparing this code.
- *
- * Most importantly, thanks to Robert Bringman <rob@mars.trion.com>
- * for supplying a Promise UDMA board & WD UDMA drive for this work!
- *
- * And, yes, Intel Zappa boards really *do* use both PIIX IDE ports.
- *
- * ATA-66/100 and recovery functions, I forgot the rest......
- */
-
-#include <linux/config.h>
-#define __NO_VERSION__
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/ide.h>
-#include <linux/delay.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-
-/*
- * Long lost data from 2.0.34 that is now in 2.0.39
- *
- * This was used in ./drivers/block/triton.c to do DMA Base address setup
- * when PnP failed. Oh the things we forget. I believe this was part
- * of SFF-8038i that has been withdrawn from public access... :-((
- */
-#define DEFAULT_BMIBA 0xe800 /* in case BIOS did not init it */
-#define DEFAULT_BMCRBA 0xcc00 /* VIA's default value */
-#define DEFAULT_BMALIBA 0xd400 /* ALI's default value */
-
-#ifdef CONFIG_IDEDMA_NEW_DRIVE_LISTINGS
-
-struct drive_list_entry {
- char * id_model;
- char * id_firmware;
-};
-
-struct drive_list_entry drive_whitelist[] = {
- { "Micropolis 2112A", NULL },
- { "CONNER CTMA 4000", NULL },
- { "CONNER CTT8000-A", NULL },
- { "ST34342A", NULL },
- { NULL, NULL }
-};
-
-struct drive_list_entry drive_blacklist[] = {
-
- { "WDC AC11000H", NULL },
- { "WDC AC22100H", NULL },
- { "WDC AC32500H", NULL },
- { "WDC AC33100H", NULL },
- { "WDC AC31600H", NULL },
- { "WDC AC32100H", "24.09P07" },
- { "WDC AC23200L", "21.10N21" },
- { "Compaq CRD-8241B", NULL },
- { "CRD-8400B", NULL },
- { "CRD-8480B", NULL },
- { "CRD-8480C", NULL },
- { "CRD-8482B", NULL },
- { "CRD-84", NULL },
- { "SanDisk SDP3B", NULL },
- { "SanDisk SDP3B-64", NULL },
- { "SANYO CD-ROM CRD", NULL },
- { "HITACHI CDR-8", NULL },
- { "HITACHI CDR-8335", NULL },
- { "HITACHI CDR-8435", NULL },
- { "Toshiba CD-ROM XM-6202B", NULL },
- { "CD-532E-A", NULL },
- { "E-IDE CD-ROM CR-840", NULL },
- { "CD-ROM Drive/F5A", NULL },
- { "RICOH CD-R/RW MP7083A", NULL },
- { "WPI CDD-820", NULL },
- { "SAMSUNG CD-ROM SC-148C", NULL },
- { "SAMSUNG CD-ROM SC-148F", NULL },
- { "SAMSUNG CD-ROM SC", NULL },
- { "SanDisk SDP3B-64", NULL },
- { "SAMSUNG CD-ROM SN-124", NULL },
- { "PLEXTOR CD-R PX-W8432T", NULL },
- { "ATAPI CD-ROM DRIVE 40X MAXIMUM", NULL },
- { "_NEC DV5800A", NULL },
- { NULL, NULL }
-
-};
-
-static int in_drive_list(struct hd_driveid *id, struct drive_list_entry * drive_table)
-{
- for ( ; drive_table->id_model ; drive_table++)
- if ((!strcmp(drive_table->id_model, id->model)) &&
- ((drive_table->id_firmware && !strstr(drive_table->id_firmware, id->fw_rev)) ||
- (!drive_table->id_firmware)))
- return 1;
- return 0;
-}
-
-#else
-
-/*
- * good_dma_drives() lists the model names (from "hdparm -i")
- * of drives which do not support mode2 DMA but which are
- * known to work fine with this interface under Linux.
- */
-const char *good_dma_drives[] = {"Micropolis 2112A",
- "CONNER CTMA 4000",
- "CONNER CTT8000-A",
- "ST34342A", /* for Sun Ultra */
- NULL};
-
-/*
- * bad_dma_drives() lists the model names (from "hdparm -i")
- * of drives which supposedly support (U)DMA but which are
- * known to corrupt data with this interface under Linux.
- *
- * This is an empirical list. Its generated from bug reports. That means
- * while it reflects actual problem distributions it doesn't answer whether
- * the drive or the controller, or cabling, or software, or some combination
- * thereof is the fault. If you don't happen to agree with the kernel's
- * opinion of your drive - use hdparm to turn DMA on.
- */
-const char *bad_dma_drives[] = {"WDC AC11000H",
- "WDC AC22100H",
- "WDC AC32100H",
- "WDC AC32500H",
- "WDC AC33100H",
- "WDC AC31600H",
- NULL};
-
-#endif
-
-/*
- * This is the handler for disk read/write DMA interrupts.
- */
-ide_startstop_t ide_dma_intr(struct ata_device *drive, struct request *rq)
-{
- u8 stat, dma_stat;
-
- dma_stat = udma_stop(drive);
- if (OK_STAT(stat = GET_STAT(),DRIVE_READY,drive->bad_wstat|DRQ_STAT)) {
- if (!dma_stat) {
- __ide_end_request(drive, rq, 1, rq->nr_sectors);
- return ide_stopped;
- }
- printk(KERN_ERR "%s: dma_intr: bad DMA status (dma_stat=%x)\n",
- drive->name, dma_stat);
- }
- return ide_error(drive, rq, "dma_intr", stat);
-}
-
-/*
- * FIXME: taskfiles should be a map of pages, not a long virt address... /jens
- * FIXME: I agree with Jens --mdcki!
- */
-static int build_sglist(struct ata_channel *ch, struct request *rq)
-{
- struct scatterlist *sg = ch->sg_table;
- int nents = 0;
-
- if (rq->flags & REQ_DRIVE_ACB) {
- struct ata_taskfile *args = rq->special;
-#if 1
- unsigned char *virt_addr = rq->buffer;
- int sector_count = rq->nr_sectors;
-#else
- nents = blk_rq_map_sg(rq->q, rq, ch->sg_table);
-
- if (nents > rq->nr_segments)
- printk("ide-dma: received %d segments, build %d\n", rq->nr_segments, nents);
-#endif
-
- if (args->command_type == IDE_DRIVE_TASK_RAW_WRITE)
- ch->sg_dma_direction = PCI_DMA_TODEVICE;
- else
- ch->sg_dma_direction = PCI_DMA_FROMDEVICE;
-
- /*
- * FIXME: This depends upon a hard coded page size!
- */
- if (sector_count > 128) {
- memset(&sg[nents], 0, sizeof(*sg));
-
- sg[nents].page = virt_to_page(virt_addr);
- sg[nents].offset = (unsigned long) virt_addr & ~PAGE_MASK;
- sg[nents].length = 128 * SECTOR_SIZE;
- ++nents;
- virt_addr = virt_addr + (128 * SECTOR_SIZE);
- sector_count -= 128;
- }
- memset(&sg[nents], 0, sizeof(*sg));
- sg[nents].page = virt_to_page(virt_addr);
- sg[nents].offset = (unsigned long) virt_addr & ~PAGE_MASK;
- sg[nents].length = sector_count * SECTOR_SIZE;
- ++nents;
- } else {
- nents = blk_rq_map_sg(rq->q, rq, ch->sg_table);
-
- if (rq->q && nents > rq->nr_phys_segments)
- printk("ide-dma: received %d phys segments, build %d\n", rq->nr_phys_segments, nents);
-
- if (rq_data_dir(rq) == READ)
- ch->sg_dma_direction = PCI_DMA_FROMDEVICE;
- else
- ch->sg_dma_direction = PCI_DMA_TODEVICE;
-
- }
- return pci_map_sg(ch->pci_dev, sg, nents, ch->sg_dma_direction);
-}
-
-/*
- * For both Blacklisted and Whitelisted drives.
- * This is setup to be called as an extern for future support
- * to other special driver code.
- */
-int check_drive_lists(struct ata_device *drive, int good_bad)
-{
- struct hd_driveid *id = drive->id;
-
-#ifdef CONFIG_IDEDMA_NEW_DRIVE_LISTINGS
- if (good_bad) {
- return in_drive_list(id, drive_whitelist);
- } else {
- int blacklist = in_drive_list(id, drive_blacklist);
- if (blacklist)
- printk("%s: Disabling (U)DMA for %s\n", drive->name, id->model);
- return(blacklist);
- }
-#else
- const char **list;
-
- if (good_bad) {
- /* Consult the list of known "good" drives */
- list = good_dma_drives;
- while (*list) {
- if (!strcmp(*list++,id->model))
- return 1;
- }
- } else {
- /* Consult the list of known "bad" drives */
- list = bad_dma_drives;
- while (*list) {
- if (!strcmp(*list++,id->model)) {
- printk("%s: Disabling (U)DMA for %s\n",
- drive->name, id->model);
- return 1;
- }
- }
- }
-#endif
- return 0;
-}
-
-static int config_drive_for_dma(struct ata_device *drive)
-{
- int config_allows_dma = 1;
- struct hd_driveid *id = drive->id;
- struct ata_channel *ch = drive->channel;
-
-#ifdef CONFIG_IDEDMA_ONLYDISK
- if (drive->type != ATA_DISK)
- config_allows_dma = 0;
-#endif
-
- if (id && (id->capability & 1) && ch->autodma && config_allows_dma) {
- /* Consult the list of known "bad" drives */
- if (udma_black_list(drive)) {
- udma_enable(drive, 0, 1);
-
- return 0;
- }
-
- /* Enable DMA on any drive that has UltraDMA (mode 6/7/?) enabled */
- if ((id->field_valid & 4) && (eighty_ninty_three(drive)))
- if ((id->dma_ultra & (id->dma_ultra >> 14) & 2)) {
- udma_enable(drive, 1, 1);
-
- return 0;
- }
- /* Enable DMA on any drive that has UltraDMA (mode 3/4/5) enabled */
- if ((id->field_valid & 4) && (eighty_ninty_three(drive)))
- if ((id->dma_ultra & (id->dma_ultra >> 11) & 7)) {
- udma_enable(drive, 1, 1);
-
- return 0;
- }
- /* Enable DMA on any drive that has UltraDMA (mode 0/1/2) enabled */
- if (id->field_valid & 4) /* UltraDMA */
- if ((id->dma_ultra & (id->dma_ultra >> 8) & 7)) {
- udma_enable(drive, 1, 1);
-
- return 0;
- }
- /* Enable DMA on any drive that has mode2 DMA (multi or single) enabled */
- if (id->field_valid & 2) /* regular DMA */
- if ((id->dma_mword & 0x404) == 0x404 || (id->dma_1word & 0x404) == 0x404) {
- udma_enable(drive, 1, 1);
-
- return 0;
- }
- /* Consult the list of known "good" drives */
- if (udma_white_list(drive)) {
- udma_enable(drive, 1, 1);
-
- return 0;
- }
- }
- udma_enable(drive, 0, 0);
-
- return 0;
-}
-
-/*
- * 1 dma-ing, 2 error, 4 intr
- */
-static int dma_timer_expiry(struct ata_device *drive, struct request *rq)
-{
- /* FIXME: What's that? */
- u8 dma_stat = inb(drive->channel->dma_base+2);
-
-#ifdef DEBUG
- printk("%s: dma_timer_expiry: dma status == 0x%02x\n", drive->name, dma_stat);
-#endif
-
-#if 0
- drive->expiry = NULL; /* one free ride for now */
-#endif
-
- if (dma_stat & 2) { /* ERROR */
- u8 stat = GET_STAT();
- return ide_error(drive, rq, "dma_timer_expiry", stat);
- }
- if (dma_stat & 1) /* DMAing */
- return WAIT_CMD;
- return 0;
-}
-
-int ata_start_dma(struct ata_device *drive, struct request *rq)
-{
- struct ata_channel *ch = drive->channel;
- unsigned long dma_base = ch->dma_base;
- unsigned int reading = 0;
-
- if (rq_data_dir(rq) == READ)
- reading = 1 << 3;
-
- /* try PIO instead of DMA */
- if (!udma_new_table(ch, rq))
- return 1;
-
- outl(ch->dmatable_dma, dma_base + 4); /* PRD table */
- outb(reading, dma_base); /* specify r/w */
- outb(inb(dma_base+2)|6, dma_base+2); /* clear INTR & ERROR flags */
- drive->waiting_for_dma = 1;
- return 0;
-}
-
-/*
- * This initiates/aborts DMA read/write operations on a drive.
- *
- * The caller is assumed to have selected the drive and programmed the drive's
- * sector address using CHS or LBA. All that remains is to prepare for DMA
- * and then issue the actual read/write DMA/PIO command to the drive.
- *
- * For ATAPI devices, we just prepare for DMA and return. The caller should
- * then issue the packet command to the drive and call us again with
- * udma_start afterwards.
- *
- * Returns 0 if all went well.
- * Returns 1 if DMA read/write could not be started, in which case
- * the caller should revert to PIO for the current request.
- * May also be invoked from trm290.c
- */
-int XXX_ide_dmaproc(struct ata_device *drive)
-{
- return config_drive_for_dma(drive);
-}
-
-/*
- * Needed for allowing full modular support of ide-driver
- */
-void ide_release_dma(struct ata_channel *ch)
-{
- if (!ch->dma_base)
- return;
-
- if (ch->dmatable_cpu) {
- pci_free_consistent(ch->pci_dev,
- PRD_ENTRIES * PRD_BYTES,
- ch->dmatable_cpu,
- ch->dmatable_dma);
- ch->dmatable_cpu = NULL;
- }
- if (ch->sg_table) {
- kfree(ch->sg_table);
- ch->sg_table = NULL;
- }
- if ((ch->dma_extra) && (ch->unit == 0))
- release_region((ch->dma_base + 16), ch->dma_extra);
- release_region(ch->dma_base, 8);
- ch->dma_base = 0;
-}
-
-/*
- * This can be called for a dynamically installed interface. Don't __init it
- */
-void ata_init_dma(struct ata_channel *ch, unsigned long dma_base)
-{
- if (!request_region(dma_base, 8, ch->name)) {
- printk(KERN_ERR "ATA: ERROR: BM DMA portst already in use!\n");
-
- return;
- }
- printk(KERN_INFO" %s: BM-DMA at 0x%04lx-0x%04lx", ch->name, dma_base, dma_base + 7);
- ch->dma_base = dma_base;
- ch->dmatable_cpu = pci_alloc_consistent(ch->pci_dev,
- PRD_ENTRIES * PRD_BYTES,
- &ch->dmatable_dma);
- if (ch->dmatable_cpu == NULL)
- goto dma_alloc_failure;
-
- ch->sg_table = kmalloc(sizeof(struct scatterlist) * PRD_ENTRIES,
- GFP_KERNEL);
- if (ch->sg_table == NULL) {
- pci_free_consistent(ch->pci_dev, PRD_ENTRIES * PRD_BYTES,
- ch->dmatable_cpu, ch->dmatable_dma);
- goto dma_alloc_failure;
- }
-
- if (!ch->XXX_udma)
- ch->XXX_udma = XXX_ide_dmaproc;
-
- if (ch->chipset != ide_trm290) {
- u8 dma_stat = inb(dma_base+2);
- printk(", BIOS settings: %s:%s, %s:%s",
- ch->drives[0].name, (dma_stat & 0x20) ? "DMA" : "pio",
- ch->drives[1].name, (dma_stat & 0x40) ? "DMA" : "pio");
- }
- printk("\n");
- return;
-
-dma_alloc_failure:
- printk(" -- ERROR, UNABLE TO ALLOCATE DMA TABLES\n");
-}
-
-/****************************************************************************
- * UDMA function which should have architecture specific counterparts where
- * neccessary.
- *
- * The intention is that at some point in time we will move this whole to
- * architecture specific kernel sections. For now I would love the architecture
- * maintainers to just #ifdef #endif this stuff directly here. I have for now
- * tryed to update as much as I could in the architecture specific code. But
- * of course I may have done mistakes, so please bear with me and update it
- * here the proper way.
- *
- * Thank you a lot in advance!
- *
- * Sat May 4 20:29:46 CEST 2002 Marcin Dalecki.
- */
-
-/*
- * This is the generic part of the DMA setup used by the host chipset drivers
- * in the corresponding DMA setup method.
- *
- * FIXME: there are some places where this gets used driectly for "error
- * recovery" in the ATAPI drivers. This was just plain wrong before, in esp.
- * not portable, and just got uncovered now.
- */
-void udma_enable(struct ata_device *drive, int on, int verbose)
-{
- struct ata_channel *ch = drive->channel;
- int set_high = 1;
- u8 unit;
- u64 addr;
-
-
- /* Method overloaded by host chip specific code. */
- if (ch->udma_enable) {
- ch->udma_enable(drive, on, verbose);
-
- return;
- }
-
- /* Fall back to the default implementation. */
- unit = (drive->select.b.unit & 0x01);
- addr = BLK_BOUNCE_HIGH;
-
- if (!on) {
- if (verbose)
- printk("%s: DMA disabled\n", drive->name);
- set_high = 0;
- outb(inb(ch->dma_base + 2) & ~(1 << (5 + unit)), ch->dma_base + 2);
-#ifdef CONFIG_BLK_DEV_IDE_TCQ
- udma_tcq_enable(drive, 0);
-#endif
- }
-
- /* toggle bounce buffers */
-
- if (on && drive->type == ATA_DISK && drive->channel->highmem) {
- if (!PCI_DMA_BUS_IS_PHYS)
- addr = BLK_BOUNCE_ANY;
- else
- addr = drive->channel->pci_dev->dma_mask;
- }
-
- blk_queue_bounce_limit(&drive->queue, addr);
-
- drive->using_dma = on;
-
- if (on) {
- outb(inb(ch->dma_base + 2) | (1 << (5 + unit)), ch->dma_base + 2);
-#ifdef CONFIG_BLK_DEV_IDE_TCQ_DEFAULT
- udma_tcq_enable(drive, 1);
-#endif
- }
-}
-
-/*
- * This prepares a dma request. Returns 0 if all went okay, returns 1
- * otherwise. May also be invoked from trm290.c
- */
-int udma_new_table(struct ata_channel *ch, struct request *rq)
-{
- unsigned int *table = ch->dmatable_cpu;
-#ifdef CONFIG_BLK_DEV_TRM290
- unsigned int is_trm290_chipset = (ch->chipset == ide_trm290);
-#else
- const int is_trm290_chipset = 0;
-#endif
- unsigned int count = 0;
- int i;
- struct scatterlist *sg;
-
- ch->sg_nents = i = build_sglist(ch, rq);
- if (!i)
- return 0;
-
- sg = ch->sg_table;
- while (i) {
- u32 cur_addr;
- u32 cur_len;
-
- cur_addr = sg_dma_address(sg);
- cur_len = sg_dma_len(sg);
-
- /*
- * Fill in the dma table, without crossing any 64kB boundaries.
- * Most hardware requires 16-bit alignment of all blocks,
- * but the trm290 requires 32-bit alignment.
- */
-
- while (cur_len) {
- u32 xcount, bcount = 0x10000 - (cur_addr & 0xffff);
-
- if (count++ >= PRD_ENTRIES) {
- printk("ide-dma: count %d, sg_nents %d, cur_len %d, cur_addr %u\n",
- count, ch->sg_nents, cur_len, cur_addr);
- BUG();
- }
-
- if (bcount > cur_len)
- bcount = cur_len;
- *table++ = cpu_to_le32(cur_addr);
- xcount = bcount & 0xffff;
- if (is_trm290_chipset)
- xcount = ((xcount >> 2) - 1) << 16;
- if (xcount == 0x0000) {
- /*
- * Most chipsets correctly interpret a length of
- * 0x0000 as 64KB, but at least one (e.g. CS5530)
- * misinterprets it as zero (!). So here we break
- * the 64KB entry into two 32KB entries instead.
- */
- if (count++ >= PRD_ENTRIES) {
- pci_unmap_sg(ch->pci_dev, sg,
- ch->sg_nents,
- ch->sg_dma_direction);
- return 0;
- }
-
- *table++ = cpu_to_le32(0x8000);
- *table++ = cpu_to_le32(cur_addr + 0x8000);
- xcount = 0x8000;
- }
- *table++ = cpu_to_le32(xcount);
- cur_addr += bcount;
- cur_len -= bcount;
- }
-
- sg++;
- i--;
- }
-
- if (!count)
- printk(KERN_ERR "%s: empty DMA table?\n", ch->name);
- else if (!is_trm290_chipset)
- *--table |= cpu_to_le32(0x80000000);
-
- return count;
-}
-
-/* Teardown mappings after DMA has completed. */
-void udma_destroy_table(struct ata_channel *ch)
-{
- pci_unmap_sg(ch->pci_dev, ch->sg_table, ch->sg_nents, ch->sg_dma_direction);
-}
-
-void udma_print(struct ata_device *drive)
-{
-#ifdef CONFIG_ARCH_ACORN
- printk(", DMA");
-#else
- struct hd_driveid *id = drive->id;
- char *str = NULL;
-
- if ((id->field_valid & 4) && (eighty_ninty_three(drive)) &&
- (id->dma_ultra & (id->dma_ultra >> 14) & 3)) {
- if ((id->dma_ultra >> 15) & 1)
- str = ", UDMA(mode 7)"; /* UDMA BIOS-enabled! */
- else
- str = ", UDMA(133)"; /* UDMA BIOS-enabled! */
- } else if ((id->field_valid & 4) && (eighty_ninty_three(drive)) &&
- (id->dma_ultra & (id->dma_ultra >> 11) & 7)) {
- if ((id->dma_ultra >> 13) & 1) {
- str = ", UDMA(100)"; /* UDMA BIOS-enabled! */
- } else if ((id->dma_ultra >> 12) & 1) {
- str = ", UDMA(66)"; /* UDMA BIOS-enabled! */
- } else {
- str = ", UDMA(44)"; /* UDMA BIOS-enabled! */
- }
- } else if ((id->field_valid & 4) &&
- (id->dma_ultra & (id->dma_ultra >> 8) & 7)) {
- if ((id->dma_ultra >> 10) & 1) {
- str = ", UDMA(33)"; /* UDMA BIOS-enabled! */
- } else if ((id->dma_ultra >> 9) & 1) {
- str = ", UDMA(25)"; /* UDMA BIOS-enabled! */
- } else {
- str = ", UDMA(16)"; /* UDMA BIOS-enabled! */
- }
- } else if (id->field_valid & 4)
- str = ", (U)DMA"; /* Can be BIOS-enabled! */
- else
- str = ", DMA";
-
- printk(str);
-#endif
-}
-
-/*
- * Drive back/white list handling for UDMA capability:
- */
-
-int udma_black_list(struct ata_device *drive)
-{
- return check_drive_lists(drive, 0);
-}
-
-int udma_white_list(struct ata_device *drive)
-{
- return check_drive_lists(drive, 1);
-}
-
-/*
- * Generic entry points for functions provided possibly by the host chip set
- * drivers.
- */
-
-/*
- * Prepare the channel for a DMA startfer. Please note that only the broken
- * Pacific Digital host chip needs the reques to be passed there to decide
- * about addressing modes.
- */
-
-int udma_start(struct ata_device *drive, struct request *rq)
-{
- struct ata_channel *ch = drive->channel;
- unsigned long dma_base = ch->dma_base;
-
- if (ch->udma_start)
- return ch->udma_start(drive, rq);
-
- /* Note that this is done *after* the cmd has
- * been issued to the drive, as per the BM-IDE spec.
- * The Promise Ultra33 doesn't work correctly when
- * we do this part before issuing the drive cmd.
- */
- outb(inb(dma_base)|1, dma_base); /* start DMA */
- return 0;
-}
-
-int udma_stop(struct ata_device *drive)
-{
- struct ata_channel *ch = drive->channel;
- unsigned long dma_base = ch->dma_base;
- u8 dma_stat;
-
- if (ch->udma_stop)
- return ch->udma_stop(drive);
-
- drive->waiting_for_dma = 0;
- outb(inb(dma_base)&~1, dma_base); /* stop DMA */
- dma_stat = inb(dma_base+2); /* get DMA status */
- outb(dma_stat|6, dma_base+2); /* clear the INTR & ERROR bits */
- udma_destroy_table(ch); /* purge DMA mappings */
-
- return (dma_stat & 7) != 4 ? (0x10 | dma_stat) : 0; /* verify good DMA status */
-}
-
-/*
- * This is the default read write function.
- *
- * It's exported only for host chips which use it for fallback or (too) late
- * capability checking.
- */
-
-int ata_do_udma(unsigned int reading, struct ata_device *drive, struct request *rq)
-{
- if (ata_start_dma(drive, rq))
- return 1;
-
- if (drive->type != ATA_DISK)
- return 0;
-
- reading <<= 3;
-
- ide_set_handler(drive, ide_dma_intr, WAIT_CMD, dma_timer_expiry); /* issue cmd to drive */
- if ((rq->flags & REQ_DRIVE_ACB) && (drive->addressing == 1)) {
- struct ata_taskfile *args = rq->special;
-
- OUT_BYTE(args->taskfile.command, IDE_COMMAND_REG);
- } else if (drive->addressing) {
- OUT_BYTE(reading ? WIN_READDMA_EXT : WIN_WRITEDMA_EXT, IDE_COMMAND_REG);
- } else {
- OUT_BYTE(reading ? WIN_READDMA : WIN_WRITEDMA, IDE_COMMAND_REG);
- }
-
- return udma_start(drive, rq);
-}
-
-int udma_read(struct ata_device *drive, struct request *rq)
-{
- struct ata_channel *ch = drive->channel;
-
- if (ch->udma_read)
- return ch->udma_read(drive, rq);
-
- return ata_do_udma(1, drive, rq);
-}
-
-int udma_write(struct ata_device *drive, struct request *rq)
-{
- struct ata_channel *ch = drive->channel;
-
- if (ch->udma_write)
- return ch->udma_write(drive, rq);
-
- return ata_do_udma(0, drive, rq);
-}
-
-/*
- * FIXME: This should be attached to a channel as we can see now!
- */
-int udma_irq_status(struct ata_device *drive)
-{
- struct ata_channel *ch = drive->channel;
- u8 dma_stat;
-
- if (ch->udma_irq_status)
- return ch->udma_irq_status(drive);
-
- /* default action */
- dma_stat = inb(ch->dma_base + 2);
-
- return (dma_stat & 4) == 4; /* return 1 if INTR asserted */
-}
-
-void udma_timeout(struct ata_device *drive)
-{
- printk(KERN_ERR "ATA: UDMA timeout occured %s!\n", drive->name);
-
- /* Invoke the chipset specific handler now. */
- if (drive->channel->udma_timeout)
- drive->channel->udma_timeout(drive);
-
-}
-
-void udma_irq_lost(struct ata_device *drive)
-{
- if (drive->channel->udma_irq_lost)
- drive->channel->udma_irq_lost(drive);
-}
-
-EXPORT_SYMBOL(udma_enable);
-EXPORT_SYMBOL(udma_start);
-EXPORT_SYMBOL(udma_stop);
-EXPORT_SYMBOL(udma_read);
-EXPORT_SYMBOL(udma_write);
-EXPORT_SYMBOL(ata_do_udma);
-EXPORT_SYMBOL(udma_irq_status);
-EXPORT_SYMBOL(udma_print);
-EXPORT_SYMBOL(udma_black_list);
-EXPORT_SYMBOL(udma_white_list);
if (!ide_end_request(drive, rq, 1))
return ide_stopped;
- if ((rq->current_nr_sectors==1) ^ (stat & DRQ_STAT)) {
+ if ((rq->nr_sectors == 1) != (stat & DRQ_STAT)) {
pBuf = ide_map_rq(rq, &flags);
DTF("write: %p, rq->current_nr_sectors: %d\n", pBuf, (int) rq->current_nr_sectors);
}
/*
- * Select the next device which will be serviced. This selects onlt between
+ * Select the next device which will be serviced. This selects only between
* devices on the same channel, since everything else will be scheduled on the
* queue level.
*/
--- /dev/null
+/**** vi:set ts=8 sts=8 sw=8:************************************************
+ *
+ * Copyright (C) 2002 Marcin Dalecki <martin@dalecki.de>
+ *
+ * Based on previous work by:
+ *
+ * Copyright (c) 1999-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (c) 1995-1998 Mark Lord
+ *
+ * May be copied or modified under the terms of the GNU General Public License
+ */
+
+/*
+ * Those are the generic BM DMA support functions for PCI bus based systems.
+ */
+
+#include <linux/config.h>
+#define __NO_VERSION__
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/ide.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#define DEFAULT_BMIBA 0xe800 /* in case BIOS did not init it */
+#define DEFAULT_BMCRBA 0xcc00 /* VIA's default value */
+#define DEFAULT_BMALIBA 0xd400 /* ALI's default value */
+
+/*
+ * This is the handler for disk read/write DMA interrupts.
+ */
+ide_startstop_t ide_dma_intr(struct ata_device *drive, struct request *rq)
+{
+ u8 stat, dma_stat;
+
+ dma_stat = udma_stop(drive);
+ if (OK_STAT(stat = GET_STAT(),DRIVE_READY,drive->bad_wstat|DRQ_STAT)) {
+ if (!dma_stat) {
+ __ide_end_request(drive, rq, 1, rq->nr_sectors);
+ return ide_stopped;
+ }
+ printk(KERN_ERR "%s: dma_intr: bad DMA status (dma_stat=%x)\n",
+ drive->name, dma_stat);
+ }
+ return ide_error(drive, rq, "dma_intr", stat);
+}
+
+/*
+ * FIXME: taskfiles should be a map of pages, not a long virt address... /jens
+ * FIXME: I agree with Jens --mdcki!
+ */
+static int build_sglist(struct ata_channel *ch, struct request *rq)
+{
+ struct scatterlist *sg = ch->sg_table;
+ int nents = 0;
+
+ if (rq->flags & REQ_DRIVE_ACB) {
+ struct ata_taskfile *args = rq->special;
+#if 1
+ unsigned char *virt_addr = rq->buffer;
+ int sector_count = rq->nr_sectors;
+#else
+ nents = blk_rq_map_sg(rq->q, rq, ch->sg_table);
+
+ if (nents > rq->nr_segments)
+ printk("ide-dma: received %d segments, build %d\n", rq->nr_segments, nents);
+#endif
+
+ if (args->command_type == IDE_DRIVE_TASK_RAW_WRITE)
+ ch->sg_dma_direction = PCI_DMA_TODEVICE;
+ else
+ ch->sg_dma_direction = PCI_DMA_FROMDEVICE;
+
+ /*
+ * FIXME: This depends upon a hard coded page size!
+ */
+ if (sector_count > 128) {
+ memset(&sg[nents], 0, sizeof(*sg));
+
+ sg[nents].page = virt_to_page(virt_addr);
+ sg[nents].offset = (unsigned long) virt_addr & ~PAGE_MASK;
+ sg[nents].length = 128 * SECTOR_SIZE;
+ ++nents;
+ virt_addr = virt_addr + (128 * SECTOR_SIZE);
+ sector_count -= 128;
+ }
+ memset(&sg[nents], 0, sizeof(*sg));
+ sg[nents].page = virt_to_page(virt_addr);
+ sg[nents].offset = (unsigned long) virt_addr & ~PAGE_MASK;
+ sg[nents].length = sector_count * SECTOR_SIZE;
+ ++nents;
+ } else {
+ nents = blk_rq_map_sg(rq->q, rq, ch->sg_table);
+
+ if (rq->q && nents > rq->nr_phys_segments)
+ printk("ide-dma: received %d phys segments, build %d\n", rq->nr_phys_segments, nents);
+
+ if (rq_data_dir(rq) == READ)
+ ch->sg_dma_direction = PCI_DMA_FROMDEVICE;
+ else
+ ch->sg_dma_direction = PCI_DMA_TODEVICE;
+
+ }
+
+ return pci_map_sg(ch->pci_dev, sg, nents, ch->sg_dma_direction);
+}
+
+/*
+ * 1 dma-ing, 2 error, 4 intr
+ */
+static int dma_timer_expiry(struct ata_device *drive, struct request *rq)
+{
+ /* FIXME: What's that? */
+ u8 dma_stat = inb(drive->channel->dma_base+2);
+
+#ifdef DEBUG
+ printk("%s: dma_timer_expiry: dma status == 0x%02x\n", drive->name, dma_stat);
+#endif
+
+#if 0
+ drive->expiry = NULL; /* one free ride for now */
+#endif
+
+ if (dma_stat & 2) { /* ERROR */
+ u8 stat = GET_STAT();
+ return ide_error(drive, rq, "dma_timer_expiry", stat);
+ }
+ if (dma_stat & 1) /* DMAing */
+ return WAIT_CMD;
+ return 0;
+}
+
+int ata_start_dma(struct ata_device *drive, struct request *rq)
+{
+ struct ata_channel *ch = drive->channel;
+ unsigned long dma_base = ch->dma_base;
+ unsigned int reading = 0;
+
+ if (rq_data_dir(rq) == READ)
+ reading = 1 << 3;
+
+ /* try PIO instead of DMA */
+ if (!udma_new_table(ch, rq))
+ return 1;
+
+ outl(ch->dmatable_dma, dma_base + 4); /* PRD table */
+ outb(reading, dma_base); /* specify r/w */
+ outb(inb(dma_base+2)|6, dma_base+2); /* clear INTR & ERROR flags */
+ drive->waiting_for_dma = 1;
+
+ return 0;
+}
+
+/*
+ * Configure a device for DMA operation.
+ */
+int XXX_ide_dmaproc(struct ata_device *drive)
+{
+ int config_allows_dma = 1;
+ struct hd_driveid *id = drive->id;
+ struct ata_channel *ch = drive->channel;
+
+#ifdef CONFIG_IDEDMA_ONLYDISK
+ if (drive->type != ATA_DISK)
+ config_allows_dma = 0;
+#endif
+
+ if (id && (id->capability & 1) && ch->autodma && config_allows_dma) {
+ /* Consult the list of known "bad" drives */
+ if (udma_black_list(drive)) {
+ udma_enable(drive, 0, 1);
+
+ return 0;
+ }
+
+ /* Enable DMA on any drive that has UltraDMA (mode 6/7/?) enabled */
+ if ((id->field_valid & 4) && (eighty_ninty_three(drive)))
+ if ((id->dma_ultra & (id->dma_ultra >> 14) & 2)) {
+ udma_enable(drive, 1, 1);
+
+ return 0;
+ }
+ /* Enable DMA on any drive that has UltraDMA (mode 3/4/5) enabled */
+ if ((id->field_valid & 4) && (eighty_ninty_three(drive)))
+ if ((id->dma_ultra & (id->dma_ultra >> 11) & 7)) {
+ udma_enable(drive, 1, 1);
+
+ return 0;
+ }
+ /* Enable DMA on any drive that has UltraDMA (mode 0/1/2) enabled */
+ if (id->field_valid & 4) /* UltraDMA */
+ if ((id->dma_ultra & (id->dma_ultra >> 8) & 7)) {
+ udma_enable(drive, 1, 1);
+
+ return 0;
+ }
+ /* Enable DMA on any drive that has mode2 DMA (multi or single) enabled */
+ if (id->field_valid & 2) /* regular DMA */
+ if ((id->dma_mword & 0x404) == 0x404 || (id->dma_1word & 0x404) == 0x404) {
+ udma_enable(drive, 1, 1);
+
+ return 0;
+ }
+ /* Consult the list of known "good" drives */
+ if (udma_white_list(drive)) {
+ udma_enable(drive, 1, 1);
+
+ return 0;
+ }
+ }
+ udma_enable(drive, 0, 0);
+
+ return 0;
+}
+
+/*
+ * Needed for allowing full modular support of ide-driver
+ */
+void ide_release_dma(struct ata_channel *ch)
+{
+ if (!ch->dma_base)
+ return;
+
+ if (ch->dmatable_cpu) {
+ pci_free_consistent(ch->pci_dev,
+ PRD_ENTRIES * PRD_BYTES,
+ ch->dmatable_cpu,
+ ch->dmatable_dma);
+ ch->dmatable_cpu = NULL;
+ }
+ if (ch->sg_table) {
+ kfree(ch->sg_table);
+ ch->sg_table = NULL;
+ }
+ if ((ch->dma_extra) && (ch->unit == 0))
+ release_region((ch->dma_base + 16), ch->dma_extra);
+ release_region(ch->dma_base, 8);
+ ch->dma_base = 0;
+}
+
+/****************************************************************************
+ * PCI specific UDMA channel method implementations.
+ */
+
+/*
+ * This is the generic part of the DMA setup used by the host chipset drivers
+ * in the corresponding DMA setup method.
+ *
+ * FIXME: there are some places where this gets used driectly for "error
+ * recovery" in the ATAPI drivers. This was just plain wrong before, in esp.
+ * not portable, and just got uncovered now.
+ */
+static void udma_pci_enable(struct ata_device *drive, int on, int verbose)
+{
+ struct ata_channel *ch = drive->channel;
+ int set_high = 1;
+ u8 unit;
+ u64 addr;
+
+ /* Fall back to the default implementation. */
+ unit = (drive->select.b.unit & 0x01);
+ addr = BLK_BOUNCE_HIGH;
+
+ if (!on) {
+ if (verbose)
+ printk("%s: DMA disabled\n", drive->name);
+ set_high = 0;
+ outb(inb(ch->dma_base + 2) & ~(1 << (5 + unit)), ch->dma_base + 2);
+#ifdef CONFIG_BLK_DEV_IDE_TCQ
+ udma_tcq_enable(drive, 0);
+#endif
+ }
+
+ /* toggle bounce buffers */
+
+ if (on && drive->type == ATA_DISK && drive->channel->highmem) {
+ if (!PCI_DMA_BUS_IS_PHYS)
+ addr = BLK_BOUNCE_ANY;
+ else
+ addr = drive->channel->pci_dev->dma_mask;
+ }
+
+ blk_queue_bounce_limit(&drive->queue, addr);
+
+ drive->using_dma = on;
+
+ if (on) {
+ outb(inb(ch->dma_base + 2) | (1 << (5 + unit)), ch->dma_base + 2);
+#ifdef CONFIG_BLK_DEV_IDE_TCQ_DEFAULT
+ udma_tcq_enable(drive, 1);
+#endif
+ }
+}
+
+/*
+ * This prepares a dma request. Returns 0 if all went okay, returns 1
+ * otherwise. May also be invoked from trm290.c
+ */
+int udma_new_table(struct ata_channel *ch, struct request *rq)
+{
+ unsigned int *table = ch->dmatable_cpu;
+#ifdef CONFIG_BLK_DEV_TRM290
+ unsigned int is_trm290_chipset = (ch->chipset == ide_trm290);
+#else
+ const int is_trm290_chipset = 0;
+#endif
+ unsigned int count = 0;
+ int i;
+ struct scatterlist *sg;
+
+ ch->sg_nents = i = build_sglist(ch, rq);
+ if (!i)
+ return 0;
+
+ sg = ch->sg_table;
+ while (i) {
+ u32 cur_addr;
+ u32 cur_len;
+
+ cur_addr = sg_dma_address(sg);
+ cur_len = sg_dma_len(sg);
+
+ /*
+ * Fill in the dma table, without crossing any 64kB boundaries.
+ * Most hardware requires 16-bit alignment of all blocks,
+ * but the trm290 requires 32-bit alignment.
+ */
+
+ while (cur_len) {
+ u32 xcount, bcount = 0x10000 - (cur_addr & 0xffff);
+
+ if (count++ >= PRD_ENTRIES) {
+ printk("ide-dma: count %d, sg_nents %d, cur_len %d, cur_addr %u\n",
+ count, ch->sg_nents, cur_len, cur_addr);
+ BUG();
+ }
+
+ if (bcount > cur_len)
+ bcount = cur_len;
+ *table++ = cpu_to_le32(cur_addr);
+ xcount = bcount & 0xffff;
+ if (is_trm290_chipset)
+ xcount = ((xcount >> 2) - 1) << 16;
+ if (xcount == 0x0000) {
+ /*
+ * Most chipsets correctly interpret a length of
+ * 0x0000 as 64KB, but at least one (e.g. CS5530)
+ * misinterprets it as zero (!). So here we break
+ * the 64KB entry into two 32KB entries instead.
+ */
+ if (count++ >= PRD_ENTRIES) {
+ pci_unmap_sg(ch->pci_dev, sg,
+ ch->sg_nents,
+ ch->sg_dma_direction);
+ return 0;
+ }
+
+ *table++ = cpu_to_le32(0x8000);
+ *table++ = cpu_to_le32(cur_addr + 0x8000);
+ xcount = 0x8000;
+ }
+ *table++ = cpu_to_le32(xcount);
+ cur_addr += bcount;
+ cur_len -= bcount;
+ }
+
+ sg++;
+ i--;
+ }
+
+ if (!count)
+ printk(KERN_ERR "%s: empty DMA table?\n", ch->name);
+ else if (!is_trm290_chipset)
+ *--table |= cpu_to_le32(0x80000000);
+
+ return count;
+}
+
+/* Teardown mappings after DMA has completed. */
+void udma_destroy_table(struct ata_channel *ch)
+{
+ pci_unmap_sg(ch->pci_dev, ch->sg_table, ch->sg_nents, ch->sg_dma_direction);
+}
+
+/*
+ * Prepare the channel for a DMA startfer. Please note that only the broken
+ * Pacific Digital host chip needs the reques to be passed there to decide
+ * about addressing modes.
+ */
+
+static int udma_pci_start(struct ata_device *drive, struct request *rq)
+{
+ struct ata_channel *ch = drive->channel;
+ unsigned long dma_base = ch->dma_base;
+
+ /* Note that this is done *after* the cmd has
+ * been issued to the drive, as per the BM-IDE spec.
+ * The Promise Ultra33 doesn't work correctly when
+ * we do this part before issuing the drive cmd.
+ */
+ outb(inb(dma_base)|1, dma_base); /* start DMA */
+ return 0;
+}
+
+static int udma_pci_stop(struct ata_device *drive)
+{
+ struct ata_channel *ch = drive->channel;
+ unsigned long dma_base = ch->dma_base;
+ u8 dma_stat;
+
+ drive->waiting_for_dma = 0;
+ outb(inb(dma_base)&~1, dma_base); /* stop DMA */
+ dma_stat = inb(dma_base+2); /* get DMA status */
+ outb(dma_stat|6, dma_base+2); /* clear the INTR & ERROR bits */
+ udma_destroy_table(ch); /* purge DMA mappings */
+
+ return (dma_stat & 7) != 4 ? (0x10 | dma_stat) : 0; /* verify good DMA status */
+}
+
+static int udma_pci_read(struct ata_device *drive, struct request *rq)
+{
+ return ata_do_udma(1, drive, rq);
+}
+
+static int udma_pci_write(struct ata_device *drive, struct request *rq)
+{
+ return ata_do_udma(0, drive, rq);
+}
+
+/*
+ * FIXME: This should be attached to a channel as we can see now!
+ */
+static int udma_pci_irq_status(struct ata_device *drive)
+{
+ struct ata_channel *ch = drive->channel;
+ u8 dma_stat;
+
+ /* default action */
+ dma_stat = inb(ch->dma_base + 2);
+
+ return (dma_stat & 4) == 4; /* return 1 if INTR asserted */
+}
+
+static void udma_pci_timeout(struct ata_device *drive)
+{
+ printk(KERN_ERR "ATA: UDMA timeout occured %s!\n", drive->name);
+}
+
+static void udma_pci_irq_lost(struct ata_device *drive)
+{
+}
+
+/*
+ * This can be called for a dynamically installed interface. Don't __init it
+ */
+void ata_init_dma(struct ata_channel *ch, unsigned long dma_base)
+{
+ if (!request_region(dma_base, 8, ch->name)) {
+ printk(KERN_ERR "ATA: ERROR: BM DMA portst already in use!\n");
+
+ return;
+ }
+ printk(KERN_INFO" %s: BM-DMA at 0x%04lx-0x%04lx", ch->name, dma_base, dma_base + 7);
+ ch->dma_base = dma_base;
+ ch->dmatable_cpu = pci_alloc_consistent(ch->pci_dev,
+ PRD_ENTRIES * PRD_BYTES,
+ &ch->dmatable_dma);
+ if (ch->dmatable_cpu == NULL)
+ goto dma_alloc_failure;
+
+ ch->sg_table = kmalloc(sizeof(struct scatterlist) * PRD_ENTRIES,
+ GFP_KERNEL);
+ if (ch->sg_table == NULL) {
+ pci_free_consistent(ch->pci_dev, PRD_ENTRIES * PRD_BYTES,
+ ch->dmatable_cpu, ch->dmatable_dma);
+ goto dma_alloc_failure;
+ }
+
+ /*
+ * We could just assign them, and then leave it up to the chipset
+ * specific code to override these after they've called this function.
+ */
+ if (!ch->XXX_udma)
+ ch->XXX_udma = XXX_ide_dmaproc;
+ if (!ch->udma_enable)
+ ch->udma_enable = udma_pci_enable;
+ if (!ch->udma_start)
+ ch->udma_start = udma_pci_start;
+ if (!ch->udma_stop)
+ ch->udma_stop = udma_pci_stop;
+ if (!ch->udma_read)
+ ch->udma_read = udma_pci_read;
+ if (!ch->udma_write)
+ ch->udma_write = udma_pci_write;
+ if (!ch->udma_irq_status)
+ ch->udma_irq_status = udma_pci_irq_status;
+ if (!ch->udma_timeout)
+ ch->udma_timeout = udma_pci_timeout;
+ if (!ch->udma_irq_lost)
+ ch->udma_irq_lost = udma_pci_irq_lost;
+
+ if (ch->chipset != ide_trm290) {
+ u8 dma_stat = inb(dma_base+2);
+ printk(", BIOS settings: %s:%s, %s:%s",
+ ch->drives[0].name, (dma_stat & 0x20) ? "DMA" : "pio",
+ ch->drives[1].name, (dma_stat & 0x40) ? "DMA" : "pio");
+ }
+ printk("\n");
+ return;
+
+dma_alloc_failure:
+ printk(" -- ERROR, UNABLE TO ALLOCATE DMA TABLES\n");
+}
+
+/*
+ * This is the default read write function.
+ *
+ * It's exported only for host chips which use it for fallback or (too) late
+ * capability checking.
+ */
+
+int ata_do_udma(unsigned int reading, struct ata_device *drive, struct request *rq)
+{
+ if (ata_start_dma(drive, rq))
+ return 1;
+
+ if (drive->type != ATA_DISK)
+ return 0;
+
+ reading <<= 3;
+
+ ide_set_handler(drive, ide_dma_intr, WAIT_CMD, dma_timer_expiry); /* issue cmd to drive */
+ if ((rq->flags & REQ_DRIVE_ACB) && (drive->addressing == 1)) {
+ struct ata_taskfile *args = rq->special;
+
+ outb(args->taskfile.command, IDE_COMMAND_REG);
+ } else if (drive->addressing) {
+ outb(reading ? WIN_READDMA_EXT : WIN_WRITEDMA_EXT, IDE_COMMAND_REG);
+ } else {
+ outb(reading ? WIN_READDMA : WIN_WRITEDMA, IDE_COMMAND_REG);
+ }
+
+ return udma_start(drive, rq);
+}
+
+EXPORT_SYMBOL(ata_do_udma);
+EXPORT_SYMBOL(ide_dma_intr);
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59 Temple
- * Place, Suite 330, Boston, MA 02111-1307 USA
*/
/*
#define PDC202XX_DEBUG_DRIVE_INFO 0
#define PDC202XX_DECODE_REGISTER_INFO 0
-#undef DISPLAY_PDC202XX_TIMINGS
-
#ifndef SPLIT_BYTE
#define SPLIT_BYTE(B,H,L) ((H)=(B>>4), (L)=(B-((B>>4)<<4)))
#endif
-#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS)
-#include <linux/stat.h>
-#include <linux/proc_fs.h>
-
-static int pdc202xx_get_info(char *, char **, off_t, int);
-extern int (*pdc202xx_display_info)(char *, char **, off_t, int); /* ide-proc.c */
-static struct pci_dev *bmide_dev;
-
-char *pdc202xx_pio_verbose (u32 drive_pci)
-{
- if ((drive_pci & 0x000ff000) == 0x000ff000) return("NOTSET");
- if ((drive_pci & 0x00000401) == 0x00000401) return("PIO 4");
- if ((drive_pci & 0x00000602) == 0x00000602) return("PIO 3");
- if ((drive_pci & 0x00000803) == 0x00000803) return("PIO 2");
- if ((drive_pci & 0x00000C05) == 0x00000C05) return("PIO 1");
- if ((drive_pci & 0x00001309) == 0x00001309) return("PIO 0");
- return("PIO ?");
-}
-
-char *pdc202xx_dma_verbose (u32 drive_pci)
-{
- if ((drive_pci & 0x00036000) == 0x00036000) return("MWDMA 2");
- if ((drive_pci & 0x00046000) == 0x00046000) return("MWDMA 1");
- if ((drive_pci & 0x00056000) == 0x00056000) return("MWDMA 0");
- if ((drive_pci & 0x00056000) == 0x00056000) return("SWDMA 2");
- if ((drive_pci & 0x00068000) == 0x00068000) return("SWDMA 1");
- if ((drive_pci & 0x000BC000) == 0x000BC000) return("SWDMA 0");
- return("PIO---");
-}
-
-char *pdc202xx_ultra_verbose (u32 drive_pci, u16 slow_cable)
-{
- if ((drive_pci & 0x000ff000) == 0x000ff000)
- return("NOTSET");
- if ((drive_pci & 0x00012000) == 0x00012000)
- return((slow_cable) ? "UDMA 2" : "UDMA 4");
- if ((drive_pci & 0x00024000) == 0x00024000)
- return((slow_cable) ? "UDMA 1" : "UDMA 3");
- if ((drive_pci & 0x00036000) == 0x00036000)
- return("UDMA 0");
- return(pdc202xx_dma_verbose(drive_pci));
-}
-
-static char * pdc202xx_info (char *buf, struct pci_dev *dev)
-{
- char *p = buf;
-
- u32 bibma = pci_resource_start(dev, 4);
- u32 reg60h = 0, reg64h = 0, reg68h = 0, reg6ch = 0;
- u16 reg50h = 0, pmask = (1<<10), smask = (1<<11);
- u8 hi = 0, lo = 0;
-
- /*
- * at that point bibma+0x2 et bibma+0xa are byte registers
- * to investigate:
- */
- u8 c0 = inb_p((unsigned short)bibma + 0x02);
- u8 c1 = inb_p((unsigned short)bibma + 0x0a);
-
- u8 sc11 = inb_p((unsigned short)bibma + 0x11);
- u8 sc1a = inb_p((unsigned short)bibma + 0x1a);
- u8 sc1b = inb_p((unsigned short)bibma + 0x1b);
- u8 sc1c = inb_p((unsigned short)bibma + 0x1c);
- u8 sc1d = inb_p((unsigned short)bibma + 0x1d);
- u8 sc1e = inb_p((unsigned short)bibma + 0x1e);
- u8 sc1f = inb_p((unsigned short)bibma + 0x1f);
-
- pci_read_config_word(dev, 0x50, ®50h);
- pci_read_config_dword(dev, 0x60, ®60h);
- pci_read_config_dword(dev, 0x64, ®64h);
- pci_read_config_dword(dev, 0x68, ®68h);
- pci_read_config_dword(dev, 0x6c, ®6ch);
-
- switch(dev->device) {
- case PCI_DEVICE_ID_PROMISE_20267:
- p += sprintf(p, "\n PDC20267 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20265:
- p += sprintf(p, "\n PDC20265 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20262:
- p += sprintf(p, "\n PDC20262 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20246:
- p += sprintf(p, "\n PDC20246 Chipset.\n");
- reg50h |= 0x0c00;
- break;
- default:
- p += sprintf(p, "\n PDC202XX Chipset.\n");
- break;
- }
-
- p += sprintf(p, "------------------------------- General Status ---------------------------------\n");
- p += sprintf(p, "Burst Mode : %sabled\n", (sc1f & 0x01) ? "en" : "dis");
- p += sprintf(p, "Host Mode : %s\n", (sc1f & 0x08) ? "Tri-Stated" : "Normal");
- p += sprintf(p, "Bus Clocking : %s\n",
- ((sc1f & 0xC0) == 0xC0) ? "100 External" :
- ((sc1f & 0x80) == 0x80) ? "66 External" :
- ((sc1f & 0x40) == 0x40) ? "33 External" : "33 PCI Internal");
- p += sprintf(p, "IO pad select : %s mA\n",
- ((sc1c & 0x03) == 0x03) ? "10" :
- ((sc1c & 0x02) == 0x02) ? "8" :
- ((sc1c & 0x01) == 0x01) ? "6" :
- ((sc1c & 0x00) == 0x00) ? "4" : "??");
- SPLIT_BYTE(sc1e, hi, lo);
- p += sprintf(p, "Status Polling Period : %d\n", hi);
- p += sprintf(p, "Interrupt Check Status Polling Delay : %d\n", lo);
- p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n");
- p += sprintf(p, " %s %s\n",
- (c0&0x80)?"disabled":"enabled ",
- (c1&0x80)?"disabled":"enabled ");
- p += sprintf(p, "66 Clocking %s %s\n",
- (sc11&0x02)?"enabled ":"disabled",
- (sc11&0x08)?"enabled ":"disabled");
- p += sprintf(p, " Mode %s Mode %s\n",
- (sc1a & 0x01) ? "MASTER" : "PCI ",
- (sc1b & 0x01) ? "MASTER" : "PCI ");
- p += sprintf(p, " %s %s\n",
- (sc1d & 0x08) ? "Error " :
- ((sc1d & 0x05) == 0x05) ? "Not My INTR " :
- (sc1d & 0x04) ? "Interrupting" :
- (sc1d & 0x02) ? "FIFO Full " :
- (sc1d & 0x01) ? "FIFO Empty " : "????????????",
- (sc1d & 0x80) ? "Error " :
- ((sc1d & 0x50) == 0x50) ? "Not My INTR " :
- (sc1d & 0x40) ? "Interrupting" :
- (sc1d & 0x20) ? "FIFO Full " :
- (sc1d & 0x10) ? "FIFO Empty " : "????????????");
- p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n");
- p += sprintf(p, "DMA enabled: %s %s %s %s\n",
- (c0&0x20)?"yes":"no ",(c0&0x40)?"yes":"no ",(c1&0x20)?"yes":"no ",(c1&0x40)?"yes":"no ");
- p += sprintf(p, "DMA Mode: %s %s %s %s\n",
- pdc202xx_ultra_verbose(reg60h, (reg50h & pmask)),
- pdc202xx_ultra_verbose(reg64h, (reg50h & pmask)),
- pdc202xx_ultra_verbose(reg68h, (reg50h & smask)),
- pdc202xx_ultra_verbose(reg6ch, (reg50h & smask)));
- p += sprintf(p, "PIO Mode: %s %s %s %s\n",
- pdc202xx_pio_verbose(reg60h),
- pdc202xx_pio_verbose(reg64h),
- pdc202xx_pio_verbose(reg68h),
- pdc202xx_pio_verbose(reg6ch));
-#if 0
- p += sprintf(p, "--------------- Can ATAPI DMA ---------------\n");
-#endif
- return (char *)p;
-}
-
-static char * pdc202xx_info_new (char *buf, struct pci_dev *dev)
-{
- char *p = buf;
-// u32 bibma = pci_resource_start(dev, 4);
-
-// u32 reg60h = 0, reg64h = 0, reg68h = 0, reg6ch = 0;
-// u16 reg50h = 0, word88 = 0;
-// int udmasel[4]={0,0,0,0}, piosel[4]={0,0,0,0}, i=0, hd=0;
-
- switch(dev->device) {
- case PCI_DEVICE_ID_PROMISE_20275:
- p += sprintf(p, "\n PDC20275 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20276:
- p += sprintf(p, "\n PDC20276 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20269:
- p += sprintf(p, "\n PDC20269 TX2 Chipset.\n");
- break;
- case PCI_DEVICE_ID_PROMISE_20268:
- case PCI_DEVICE_ID_PROMISE_20268R:
- p += sprintf(p, "\n PDC20268 TX2 Chipset.\n");
- break;
-default:
- p += sprintf(p, "\n PDC202XX Chipset.\n");
- break;
- }
- return (char *)p;
-}
-
-static int pdc202xx_get_info (char *buffer, char **addr, off_t offset, int count)
-{
- char *p = buffer;
- switch(bmide_dev->device) {
- case PCI_DEVICE_ID_PROMISE_20275:
- case PCI_DEVICE_ID_PROMISE_20276:
- case PCI_DEVICE_ID_PROMISE_20269:
- case PCI_DEVICE_ID_PROMISE_20268:
- case PCI_DEVICE_ID_PROMISE_20268R:
- p = pdc202xx_info_new(buffer, bmide_dev);
- break;
- default:
- p = pdc202xx_info(buffer, bmide_dev);
- break;
- }
- return p-buffer; /* => must be less than 4k! */
-}
-#endif /* defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) */
-
-byte pdc202xx_proc = 0;
-
-const char *pdc_quirk_drives[] = {
- "QUANTUM FIREBALLlct08 08",
- "QUANTUM FIREBALLP KA6.4",
- "QUANTUM FIREBALLP LM20.4",
- "QUANTUM FIREBALLP KX20.5",
- "QUANTUM FIREBALLP KX27.3",
- "QUANTUM FIREBALLP LM20.5",
- NULL
-};
-
extern char *ide_xfer_verbose (byte xfer_rate);
/* A Register */
switch(registers) {
case REG_A:
- bit2 = 0;
printk("A Register ");
if (value & 0x80) printk("SYNC_IN ");
if (value & 0x40) printk("ERRDY_EN ");
printk("PIO(A) = %d ", bit2);
break;
case REG_B:
- bit1 = 0;bit2 = 0;
printk("B Register ");
if (value & 0x80) { printk("MB2 ");bit1 |= 0x80; }
if (value & 0x40) { printk("MB1 ");bit1 |= 0x40; }
printk("PIO(B) = %d ", bit2);
break;
case REG_C:
- bit2 = 0;
printk("C Register ");
if (value & 0x80) printk("DMARQp ");
if (value & 0x40) printk("IORDYp ");
#endif /* PDC202XX_DECODE_REGISTER_INFO */
-static int check_in_drive_lists(struct ata_device *drive, const char **list)
-{
+int check_in_drive_lists(struct ata_device *drive) {
+ const char *pdc_quirk_drives[] = {
+ "QUANTUM FIREBALLlct08 08",
+ "QUANTUM FIREBALLP KA6.4",
+ "QUANTUM FIREBALLP LM20.4",
+ "QUANTUM FIREBALLP KX20.5",
+ "QUANTUM FIREBALLP KX27.3",
+ "QUANTUM FIREBALLP LM20.5",
+ NULL
+ };
+ const char**list = pdc_quirk_drives;
struct hd_driveid *id = drive->id;
- if (pdc_quirk_drives == list) {
- while (*list) {
- if (strstr(id->model, *list++)) {
- return 2;
- }
- }
- } else {
- while (*list) {
- if (!strcmp(*list++,id->model)) {
- return 1;
- }
- }
- }
+ while (*list)
+ if (strstr(id->model, *list++))
+ return 2;
return 0;
}
return err;
}
+#define set_2regs(a, b) \
+ OUT_BYTE((a + adj), indexreg); \
+ OUT_BYTE(b, datareg);
+
+#define set_reg_and_wait(value, reg, delay) \
+ OUT_BYTE(value, reg); \
+ mdelay(delay);
+
+
static int pdc202xx_new_tune_chipset(struct ata_device *drive, byte speed)
{
struct ata_channel *hwif = drive->channel;
case XFER_UDMA_7:
speed = XFER_UDMA_6;
case XFER_UDMA_6:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x1a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x01, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xcb, datareg);
+ set_2regs(0x10, 0x1a);
+ set_2regs(0x11, 0x01);
+ set_2regs(0x12, 0xcb);
break;
case XFER_UDMA_5:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x1a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x02, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xcb, datareg);
+ set_2regs(0x10, 0x1a);
+ set_2regs(0x11, 0x02);
+ set_2regs(0x12, 0xcb);
break;
case XFER_UDMA_4:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x1a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x03, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xcd, datareg);
+ set_2regs(0x10, 0x1a);
+ set_2regs(0x11, 0x03);
+ set_2regs(0x12, 0xcd);
break;
case XFER_UDMA_3:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x1a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x05, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xcd, datareg);
+ set_2regs(0x10, 0x1a);
+ set_2regs(0x11, 0x05);
+ set_2regs(0x12, 0xcd);
break;
case XFER_UDMA_2:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x2a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x07, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xcd, datareg);
+ set_2regs(0x10, 0x2a);
+ set_2regs(0x11, 0x07);
+ set_2regs(0x12, 0xcd);
break;
case XFER_UDMA_1:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x3a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x0a, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xd0, datareg);
+ set_2regs(0x10, 0x3a);
+ set_2regs(0x11, 0x0a);
+ set_2regs(0x12, 0xd0);
break;
case XFER_UDMA_0:
- OUT_BYTE((0x10 + adj), indexreg);
- OUT_BYTE(0x4a, datareg);
- OUT_BYTE((0x11 + adj), indexreg);
- OUT_BYTE(0x0f, datareg);
- OUT_BYTE((0x12 + adj), indexreg);
- OUT_BYTE(0xd5, datareg);
+ set_2regs(0x10, 0x4a);
+ set_2regs(0x11, 0x0f);
+ set_2regs(0x12, 0xd5);
break;
case XFER_MW_DMA_2:
- OUT_BYTE((0x0e + adj), indexreg);
- OUT_BYTE(0x69, datareg);
- OUT_BYTE((0x0f + adj), indexreg);
- OUT_BYTE(0x25, datareg);
+ set_2regs(0x0e, 0x69);
+ set_2regs(0x0f, 0x25);
break;
case XFER_MW_DMA_1:
- OUT_BYTE((0x0e + adj), indexreg);
- OUT_BYTE(0x6b, datareg);
- OUT_BYTE((0x0f+ adj), indexreg);
- OUT_BYTE(0x27, datareg);
+ set_2regs(0x0e, 0x6b);
+ set_2regs(0x0f, 0x27);
break;
case XFER_MW_DMA_0:
- OUT_BYTE((0x0e + adj), indexreg);
- OUT_BYTE(0xdf, datareg);
- OUT_BYTE((0x0f + adj), indexreg);
- OUT_BYTE(0x5f, datareg);
+ set_2regs(0x0e, 0xdf);
+ set_2regs(0x0f, 0x5f);
break;
#else
switch (speed) {
#endif /* CONFIG_BLK_DEV_IDEDMA */
case XFER_PIO_4:
- OUT_BYTE((0x0c + adj), indexreg);
- OUT_BYTE(0x23, datareg);
- OUT_BYTE((0x0d + adj), indexreg);
- OUT_BYTE(0x09, datareg);
- OUT_BYTE((0x13 + adj), indexreg);
- OUT_BYTE(0x25, datareg);
+ set_2regs(0x0c, 0x23);
+ set_2regs(0x0d, 0x09);
+ set_2regs(0x13, 0x25);
break;
case XFER_PIO_3:
- OUT_BYTE((0x0c + adj), indexreg);
- OUT_BYTE(0x27, datareg);
- OUT_BYTE((0x0d + adj), indexreg);
- OUT_BYTE(0x0d, datareg);
- OUT_BYTE((0x13 + adj), indexreg);
- OUT_BYTE(0x35, datareg);
+ set_2regs(0x0c, 0x27);
+ set_2regs(0x0d, 0x0d);
+ set_2regs(0x13, 0x35);
break;
case XFER_PIO_2:
- OUT_BYTE((0x0c + adj), indexreg);
- OUT_BYTE(0x23, datareg);
- OUT_BYTE((0x0d + adj), indexreg);
- OUT_BYTE(0x26, datareg);
- OUT_BYTE((0x13 + adj), indexreg);
- OUT_BYTE(0x64, datareg);
+ set_2regs(0x0c, 0x23);
+ set_2regs(0x0d, 0x26);
+ set_2regs(0x13, 0x64);
break;
case XFER_PIO_1:
- OUT_BYTE((0x0c + adj), indexreg);
- OUT_BYTE(0x46, datareg);
- OUT_BYTE((0x0d + adj), indexreg);
- OUT_BYTE(0x29, datareg);
- OUT_BYTE((0x13 + adj), indexreg);
- OUT_BYTE(0xa4, datareg);
+ set_2regs(0x0c, 0x46);
+ set_2regs(0x0d, 0x29);
+ set_2regs(0x13, 0xa4);
break;
case XFER_PIO_0:
- OUT_BYTE((0x0c + adj), indexreg);
- OUT_BYTE(0xfb, datareg);
- OUT_BYTE((0x0d + adj), indexreg);
- OUT_BYTE(0x2b, datareg);
- OUT_BYTE((0x13 + adj), indexreg);
- OUT_BYTE(0xac, datareg);
+ set_2regs(0x0c, 0xfb);
+ set_2regs(0x0d, 0x2b);
+ set_2regs(0x13, 0xac);
break;
default:
;
* 180, 120, 90, 90, 90, 60, 30
* 11, 5, 4, 3, 2, 1, 0
*/
-static int config_chipset_for_pio(struct ata_device *drive, byte pio)
+static void config_chipset_for_pio(struct ata_device *drive, byte pio)
{
- byte speed = 0x00;
+ byte speed;
if (pio == 255)
speed = ata_timing_mode(drive, XFER_PIO | XFER_EPIO);
- else
- speed = XFER_PIO_0 + min_t(byte, pio, 4);
+ else speed = XFER_PIO_0 + min_t(byte, pio, 4);
- return ((int) pdc202xx_tune_chipset(drive, speed));
-}
-
-static void pdc202xx_tune_drive(struct ata_device *drive, byte pio)
-{
- (void) config_chipset_for_pio(drive, pio);
+ pdc202xx_tune_chipset(drive, speed);
}
#ifdef CONFIG_BLK_DEV_IDEDMA
if (drive->type != ATA_DISK)
return 0;
if (id->capability & 4) { /* IORDY_EN & PREFETCH_EN */
- OUT_BYTE((iordy + adj), indexreg);
- OUT_BYTE((IN_BYTE(datareg)|0x03), datareg);
+ set_2regs(iordy, (IN_BYTE(datareg)|0x03));
}
goto jumpbit_is_set;
}
on = 0;
verbose = 0;
no_dma_set:
- (void) config_chipset_for_pio(drive, 5);
+ config_chipset_for_pio(drive, 5);
}
udma_enable(drive, on, verbose);
return 0;
}
-int pdc202xx_quirkproc(struct ata_device *drive)
-{
- return ((int) check_in_drive_lists(drive, pdc_quirk_drives));
-}
-
static int pdc202xx_udma_start(struct ata_device *drive, struct request *rq)
{
u8 clock = 0;
return (dma_stat & 4) == 4; /* return 1 if INTR asserted */
}
-static void pdc202xx_udma_timeout(struct ata_device *drive)
-{
- if (!drive->channel->resetproc)
- return;
- /* Assume naively that resetting the drive may help. */
- drive->channel->resetproc(drive);
-}
-
-static void pdc202xx_udma_irq_lost(struct ata_device *drive)
+static void pdc202xx_bug (struct ata_device *drive)
{
if (!drive->channel->resetproc)
return;
void pdc202xx_new_reset(struct ata_device *drive)
{
- OUT_BYTE(0x04,IDE_CONTROL_REG);
- mdelay(1000);
- OUT_BYTE(0x00,IDE_CONTROL_REG);
- mdelay(1000);
+ set_reg_and_wait(0x04,IDE_CONTROL_REG, 1000);
+ set_reg_and_wait(0x00,IDE_CONTROL_REG, 1000);
printk("PDC202XX: %s channel reset.\n",
drive->channel->unit ? "Secondary" : "Primary");
}
unsigned long high_16 = pci_resource_start(drive->channel->pci_dev, 4);
byte udma_speed_flag = IN_BYTE(high_16 + 0x001f);
- OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
- mdelay(100);
- OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
- mdelay(2000); /* 2 seconds ?! */
+ set_reg_and_wait(udma_speed_flag | 0x10, high_16 + 0x001f, 100);
+ set_reg_and_wait(udma_speed_flag & ~0x10, high_16 + 0x001f, 2000); /* 2 seconds ?! */
printk("PDC202XX: %s channel reset.\n",
drive->channel->unit ? "Secondary" : "Primary");
}
-/*
- * Since SUN Cobalt is attempting to do this operation, I should disclose
- * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
- * HOTSWAP ATA Infrastructure.
- */
-static int pdc202xx_tristate(struct ata_device * drive, int state)
-{
-#if 0
- struct ata_channel *hwif = drive->channel;
- unsigned long high_16 = pci_resource_start(hwif->pci_dev, 4);
- byte sc1f = inb(high_16 + 0x001f);
-
- if (!hwif)
- return -EINVAL;
-
-// hwif->bus_state = state;
-
- if (state) {
- outb(sc1f | 0x08, high_16 + 0x001f);
- } else {
- outb(sc1f & ~0x08, high_16 + 0x001f);
- }
-#endif
- return 0;
-}
-
static unsigned int __init pdc202xx_init_chipset(struct pci_dev *dev)
{
unsigned long high_16 = pci_resource_start(dev, 4);
break;
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
- OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
- mdelay(100);
- OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
- mdelay(2000); /* 2 seconds ?! */
+ set_reg_and_wait(udma_speed_flag | 0x10, high_16 + 0x001f, 100);
+ set_reg_and_wait(udma_speed_flag & ~0x10, high_16 + 0x001f, 2000); /* 2 seconds ?! */
break;
case PCI_DEVICE_ID_PROMISE_20262:
/*
* reset leaves the timing registers intact,
* but resets the drives.
*/
- OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
- mdelay(100);
- OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
- mdelay(2000); /* 2 seconds ?! */
+ set_reg_and_wait(udma_speed_flag | 0x10, high_16 + 0x001f, 100);
+ set_reg_and_wait(udma_speed_flag & ~0x10, high_16 + 0x001f, 2000); /* 2 seconds ?! */
default:
if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE) {
byte irq = 0, irq2 = 0;
}
#endif /* CONFIG_PDC202XX_BURST */
-#ifdef CONFIG_PDC202XX_MASTER
- if (!(primary_mode & 1)) {
- printk("%s: FORCING PRIMARY MODE BIT 0x%02x -> 0x%02x ",
- dev->name, primary_mode, (primary_mode|1));
- OUT_BYTE(primary_mode|1, high_16 + 0x001a);
- printk("%s\n", (IN_BYTE(high_16 + 0x001a) & 1) ? "MASTER" : "PCI");
- }
-
- if (!(secondary_mode & 1)) {
- printk("%s: FORCING SECONDARY MODE BIT 0x%02x -> 0x%02x ",
- dev->name, secondary_mode, (secondary_mode|1));
- OUT_BYTE(secondary_mode|1, high_16 + 0x001b);
- printk("%s\n", (IN_BYTE(high_16 + 0x001b) & 1) ? "MASTER" : "PCI");
- }
-#endif
-
fttk_tx_series:
-
-#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS)
- if (!pdc202xx_proc) {
- pdc202xx_proc = 1;
- bmide_dev = dev;
- pdc202xx_display_info = &pdc202xx_get_info;
- }
-#endif
return dev->irq;
}
static void __init ide_init_pdc202xx(struct ata_channel *hwif)
{
- hwif->tuneproc = &pdc202xx_tune_drive;
- hwif->quirkproc = &pdc202xx_quirkproc;
+ hwif->tuneproc = &config_chipset_for_pio;
+ hwif->quirkproc = &check_in_drive_lists;
switch(hwif->pci_dev->device) {
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
case PCI_DEVICE_ID_PROMISE_20262:
- hwif->busproc = &pdc202xx_tristate;
hwif->resetproc = &pdc202xx_reset;
case PCI_DEVICE_ID_PROMISE_20246:
hwif->speedproc = &pdc202xx_tune_chipset;
break;
}
-#undef CONFIG_PDC202XX_32_UNMASK
-#ifdef CONFIG_PDC202XX_32_UNMASK
- hwif->io_32bit = 1;
- hwif->unmask = 1;
-#endif
-
#ifdef CONFIG_BLK_DEV_IDEDMA
if (hwif->dma_base) {
hwif->udma_start = pdc202xx_udma_start;
hwif->udma_stop = pdc202xx_udma_stop;
hwif->udma_irq_status = pdc202xx_udma_irq_status;
- hwif->udma_irq_lost = pdc202xx_udma_irq_lost;
- hwif->udma_timeout = pdc202xx_udma_timeout;
+ hwif->udma_irq_lost = pdc202xx_bug;
+ hwif->udma_timeout = pdc202xx_bug;
hwif->XXX_udma = pdc202xx_dmaproc;
hwif->highmem = 1;
if (!noautodma)
int __init init_pdc202xx(void)
{
- int i;
+ unsigned int i;
for (i = 0; i < ARRAY_SIZE(chipsets); ++i) {
ata_register_chipset(&chipsets[i]);
--- /dev/null
+/**** vi:set ts=8 sts=8 sw=8:************************************************
+ *
+ * Copyright (C) 2002 Marcin Dalecki <martin@dalecki.de>
+ *
+ * Copyright (c) 1999-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (c) 1995-1998 Mark Lord
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+/*
+ * Just the black and white list handling for BM-DMA operation.
+ */
+
+#include <linux/config.h>
+#define __NO_VERSION__
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/ide.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#ifdef CONFIG_IDEDMA_NEW_DRIVE_LISTINGS
+
+struct drive_list_entry {
+ char * id_model;
+ char * id_firmware;
+};
+
+struct drive_list_entry drive_whitelist[] = {
+ { "Micropolis 2112A", NULL },
+ { "CONNER CTMA 4000", NULL },
+ { "CONNER CTT8000-A", NULL },
+ { "ST34342A", NULL },
+ { NULL, NULL }
+};
+
+struct drive_list_entry drive_blacklist[] = {
+
+ { "WDC AC11000H", NULL },
+ { "WDC AC22100H", NULL },
+ { "WDC AC32500H", NULL },
+ { "WDC AC33100H", NULL },
+ { "WDC AC31600H", NULL },
+ { "WDC AC32100H", "24.09P07" },
+ { "WDC AC23200L", "21.10N21" },
+ { "Compaq CRD-8241B", NULL },
+ { "CRD-8400B", NULL },
+ { "CRD-8480B", NULL },
+ { "CRD-8480C", NULL },
+ { "CRD-8482B", NULL },
+ { "CRD-84", NULL },
+ { "SanDisk SDP3B", NULL },
+ { "SanDisk SDP3B-64", NULL },
+ { "SANYO CD-ROM CRD", NULL },
+ { "HITACHI CDR-8", NULL },
+ { "HITACHI CDR-8335", NULL },
+ { "HITACHI CDR-8435", NULL },
+ { "Toshiba CD-ROM XM-6202B", NULL },
+ { "CD-532E-A", NULL },
+ { "E-IDE CD-ROM CR-840", NULL },
+ { "CD-ROM Drive/F5A", NULL },
+ { "RICOH CD-R/RW MP7083A", NULL },
+ { "WPI CDD-820", NULL },
+ { "SAMSUNG CD-ROM SC-148C", NULL },
+ { "SAMSUNG CD-ROM SC-148F", NULL },
+ { "SAMSUNG CD-ROM SC", NULL },
+ { "SanDisk SDP3B-64", NULL },
+ { "SAMSUNG CD-ROM SN-124", NULL },
+ { "PLEXTOR CD-R PX-W8432T", NULL },
+ { "ATAPI CD-ROM DRIVE 40X MAXIMUM", NULL },
+ { "_NEC DV5800A", NULL },
+ { NULL, NULL }
+
+};
+
+static int in_drive_list(struct hd_driveid *id, struct drive_list_entry * drive_table)
+{
+ for ( ; drive_table->id_model ; drive_table++)
+ if ((!strcmp(drive_table->id_model, id->model)) &&
+ ((drive_table->id_firmware && !strstr(drive_table->id_firmware, id->fw_rev)) ||
+ (!drive_table->id_firmware)))
+ return 1;
+ return 0;
+}
+
+#else
+
+/*
+ * good_dma_drives() lists the model names (from "hdparm -i")
+ * of drives which do not support mode2 DMA but which are
+ * known to work fine with this interface under Linux.
+ */
+const char *good_dma_drives[] = {"Micropolis 2112A",
+ "CONNER CTMA 4000",
+ "CONNER CTT8000-A",
+ "ST34342A", /* for Sun Ultra */
+ NULL};
+
+/*
+ * bad_dma_drives() lists the model names (from "hdparm -i")
+ * of drives which supposedly support (U)DMA but which are
+ * known to corrupt data with this interface under Linux.
+ *
+ * This is an empirical list. Its generated from bug reports. That means
+ * while it reflects actual problem distributions it doesn't answer whether
+ * the drive or the controller, or cabling, or software, or some combination
+ * thereof is the fault. If you don't happen to agree with the kernel's
+ * opinion of your drive - use hdparm to turn DMA on.
+ */
+const char *bad_dma_drives[] = {"WDC AC11000H",
+ "WDC AC22100H",
+ "WDC AC32100H",
+ "WDC AC32500H",
+ "WDC AC33100H",
+ "WDC AC31600H",
+ NULL};
+
+#endif
+
+/*
+ * For both Blacklisted and Whitelisted drives.
+ * This is setup to be called as an extern for future support
+ * to other special driver code.
+ */
+int check_drive_lists(struct ata_device *drive, int good_bad)
+{
+ struct hd_driveid *id = drive->id;
+
+#ifdef CONFIG_IDEDMA_NEW_DRIVE_LISTINGS
+ if (good_bad) {
+ return in_drive_list(id, drive_whitelist);
+ } else {
+ int blacklist = in_drive_list(id, drive_blacklist);
+ if (blacklist)
+ printk("%s: Disabling (U)DMA for %s\n", drive->name, id->model);
+ return(blacklist);
+ }
+#else
+ const char **list;
+
+ if (good_bad) {
+ /* Consult the list of known "good" drives */
+ list = good_dma_drives;
+ while (*list) {
+ if (!strcmp(*list++,id->model))
+ return 1;
+ }
+ } else {
+ /* Consult the list of known "bad" drives */
+ list = bad_dma_drives;
+ while (*list) {
+ if (!strcmp(*list++,id->model)) {
+ printk("%s: Disabling (U)DMA for %s\n",
+ drive->name, id->model);
+ return 1;
+ }
+ }
+ }
+#endif
+ return 0;
+}
+
+void udma_print(struct ata_device *drive)
+{
+#ifdef CONFIG_ARCH_ACORN
+ printk(", DMA");
+#else
+ struct hd_driveid *id = drive->id;
+ char *str = NULL;
+
+ if ((id->field_valid & 4) && (eighty_ninty_three(drive)) &&
+ (id->dma_ultra & (id->dma_ultra >> 14) & 3)) {
+ if ((id->dma_ultra >> 15) & 1)
+ str = ", UDMA(mode 7)"; /* UDMA BIOS-enabled! */
+ else
+ str = ", UDMA(133)"; /* UDMA BIOS-enabled! */
+ } else if ((id->field_valid & 4) && (eighty_ninty_three(drive)) &&
+ (id->dma_ultra & (id->dma_ultra >> 11) & 7)) {
+ if ((id->dma_ultra >> 13) & 1) {
+ str = ", UDMA(100)"; /* UDMA BIOS-enabled! */
+ } else if ((id->dma_ultra >> 12) & 1) {
+ str = ", UDMA(66)"; /* UDMA BIOS-enabled! */
+ } else {
+ str = ", UDMA(44)"; /* UDMA BIOS-enabled! */
+ }
+ } else if ((id->field_valid & 4) &&
+ (id->dma_ultra & (id->dma_ultra >> 8) & 7)) {
+ if ((id->dma_ultra >> 10) & 1) {
+ str = ", UDMA(33)"; /* UDMA BIOS-enabled! */
+ } else if ((id->dma_ultra >> 9) & 1) {
+ str = ", UDMA(25)"; /* UDMA BIOS-enabled! */
+ } else {
+ str = ", UDMA(16)"; /* UDMA BIOS-enabled! */
+ }
+ } else if (id->field_valid & 4)
+ str = ", (U)DMA"; /* Can be BIOS-enabled! */
+ else
+ str = ", DMA";
+
+ printk(str);
+#endif
+}
+
+/*
+ * Drive back/white list handling for UDMA capability:
+ */
+
+int udma_black_list(struct ata_device *drive)
+{
+ return check_drive_lists(drive, 0);
+}
+
+int udma_white_list(struct ata_device *drive)
+{
+ return check_drive_lists(drive, 1);
+}
+
+EXPORT_SYMBOL(udma_print);
+EXPORT_SYMBOL(udma_black_list);
+EXPORT_SYMBOL(udma_white_list);
void __init ide_scan_pcibus(int scan_direction);
#endif
+
+static inline void udma_enable(struct ata_device *drive, int on, int verbose)
+{
+ drive->channel->udma_enable(drive, on, verbose);
+}
+
+static inline int udma_start(struct ata_device *drive, struct request *rq)
+{
+ return drive->channel->udma_start(drive, rq);
+}
+
+static inline int udma_stop(struct ata_device *drive)
+{
+ return drive->channel->udma_stop(drive);
+}
+
+static inline int udma_read(struct ata_device *drive, struct request *rq)
+{
+ return drive->channel->udma_read(drive, rq);
+}
+
+static inline int udma_write(struct ata_device *drive, struct request *rq)
+{
+ return drive->channel->udma_write(drive, rq);
+}
+
+static inline int udma_irq_status(struct ata_device *drive)
+{
+ return drive->channel->udma_irq_status(drive);
+}
+
+static inline void udma_timeout(struct ata_device *drive)
+{
+ return drive->channel->udma_timeout(drive);
+}
+
+static inline void udma_irq_lost(struct ata_device *drive)
+{
+ return drive->channel->udma_irq_lost(drive);
+}
+
#ifdef CONFIG_BLK_DEV_IDEDMA
extern int udma_new_table(struct ata_channel *, struct request *);
extern void udma_destroy_table(struct ata_channel *);
extern void udma_print(struct ata_device *);
-extern void udma_enable(struct ata_device *, int, int);
extern int udma_black_list(struct ata_device *);
extern int udma_white_list(struct ata_device *);
-extern void udma_timeout(struct ata_device *);
-extern void udma_irq_lost(struct ata_device *);
-extern int udma_start(struct ata_device *, struct request *rq);
-extern int udma_stop(struct ata_device *);
-extern int udma_read(struct ata_device *, struct request *rq);
-extern int udma_write(struct ata_device *, struct request *rq);
-extern int udma_irq_status(struct ata_device *);
extern int ata_do_udma(unsigned int reading, struct ata_device *drive, struct request *rq);
projects / history.git / commitdiff